China exported 9.85 million tonnes of finished steel in October, down 6.1% from September, customs data reported by Mysteel show, so the late-October surge in shipments did not lift the monthly total. For EU buyers the bigger limit is not China’s volume but the EU quota: by 6 November, 11 of China’s 22 country-specific Q4 quota lines were full and three more were above 90%. The step now: before booking Chinese long products or stainless hot-rolled strip for arrival this year, check the China order number in TARIC and agree who pays the 50% out-of-quota duty.
What the data show
According to Mysteel’s report of the General Administration of Customs figures, published on 10 November, China’s January–October steel exports were 95.50 million tonnes, 2.3% lower than a year earlier. Steel imports were 0.40 million tonnes in October and 4.46 million tonnes for the ten months, down 11.6%. Iron ore imports were 105.66 million tonnes in October. Loharo read the Mysteel report in Chinese; the customs website did not load for us, so these figures rest on that attributed report.
Reach steel buyers and importers worldwide
Put your brand in front of the people who buy and trade steel.
Advertise with LoharoLoharo check: a normal October dip, not a new high
Analysis. Shanghai Metals Market had expected October exports to rise to a new high for the year, after September’s 10.49 million tonnes. Instead the total fell by 0.64 million tonnes (9.85 − 10.49 = −0.64; −0.64 ÷ 10.49 = −6.1%). That fall matches last year’s pattern: October 2025 exports dropped 6.5% from September to 9.78 million tonnes, China Steel Market reported from the same customs series. On that basis October 2026 was 0.7% above October 2025 (9.85 ÷ 9.78 − 1). SMM’s own order survey had flagged October maintenance at a large east-China exporter. Mysteel’s weekly vessel tracking showed 2.91 million tonnes leaving in the week to 2 November (Loharo, 5 November), but that week falls mostly in November, so the two series do not contradict each other.
Where China still has EU quota room
Analysis. The Commission’s weekly report lists a separate Q4 quota line for China in 22 product categories. The table shows the lines with room left or close to the limit.
| China line (category) | Order no. | Q4 quota, t | Left on 6 Nov, t | Used |
|---|---|---|---|---|
| Rebar (13) | 09.9888 | 9,746 | 25 | 99.7% |
| Merchant bars and light sections (12) | 09.9878 | 39,546 | 75 | 99.8% |
| Cold-finished bars (27) | 09.9949 | 3,961 | 249 | 93.7% |
| Stainless hot-rolled sheet and strip (8) | 09.9863 | 4,441 | 1,212 | 72.7% |
| Stainless cold-rolled sheet and strip (9) | 09.9868 | 15,855 | 15,063 | 5.0% |
| Tin mill products (6) | 09.9848 | 52,800 | 41,092 | 22.2% |
Rebar shows how quickly a line can go: 4,702 t of Chinese rebar was drawn in the week to 6 November, against 4,727 t left on 30 October, leaving 25 t. Stainless hot-rolled sheet drew 3,041 t in the same week; at that pace its 1,212 t would last about three days (1,212 ÷ (3,041 ÷ 7) ≈ 2.8), so it may already be closed. The real room is in tin mill products and stainless cold-rolled sheet.
What it means
Analysis. For buyers of rebar, merchant bars and stainless hot-rolled strip, a Chinese offer for arrival before 31 December should be priced with the 50% duty unless the trader can show quota cover. For tin mill and stainless cold-rolled buyers, Chinese material can still enter duty-free for now, subject to any anti-dumping duties on the product. One weaker month does not change the picture of a large Chinese surplus; it mainly shows that the late-October shipping burst has not yet appeared in the customs figures.
What to watch
- DG TAXUD report dated 13 November: the next quota snapshot, for the stainless hot-rolled and tin mill lines.
- Around 20 November: China’s detailed October export breakdown by product and destination.
- 1 January 2027: Q1 quota volumes open; in the measure’s first year unused Q4 room carries over.
Verification status: Verified
- China’s October and January–October customs figures are attributed to Mysteel’s report of 10 November (read in Chinese; the customs site was unreachable), with September from SMM and October 2025 from China Steel Market. Quota figures come straight from the Commission’s 6 November and 30 October workbooks. The month-on-month, year-on-year and run-rate figures are Loharo calculations shown in the text.
Ask the Analyst
“1,000 t HRC from China into Rotterdam at €540/t CFR”: landed cost with duty, quota and CBAM in one answer.Ask the AnalystSources
Primary sources
- Report on Tariff Quota Imports — 6 November 2026 — European Commission, DG TAXUD, 6 November 2026
- Report on Tariff Quota Imports — 30 October 2026 — European Commission, DG TAXUD, 30 October 2026
- TARIC quota consultation — European Commission
Supporting sources
- Customs: China exported 9.854 Mt of steel in October (in Chinese) — Mysteel, 10 November 2026
- SMM steel import and export analysis: September export orders pick up — Shanghai Metals Market, 14 October 2026
- In October 2025, China exported 9.782 million tons of steel — China Steel Market, November 2025
Related on Loharo
- China’s steel export shipments hit a 13-week high, but its $480 coil still costs €656–800 at the EU border
- EU steel quotas four weeks into Q4
Last fact-check: 10 November 2026.
Planning steel imports into the EU? Estimate CBAM costs with the free calculator using EU default values. For supplier-specific emissions and a portfolio review, see the CBAM Cost Check.




