Assofermet, the Italian association of steel traders, distributors and processors, has asked the European Commission to raise CBAM’s yearly exemption from 50 to 500 tonnes per importer before the mechanism is extended to downstream steel and aluminium goods. For EU buyers this matters most to stockholders, fabricators and smaller importers bringing in a few hundred tonnes of coil, tube or fittings a year: on Loharo’s working, a 500-tonne limit would take up to about €139,000 a year of CBAM cost on Indian hot-rolled coil out of scope for one such importer. It is a request, not a rule. No step needed yet on contracts: keep budgeting CBAM under the 50-tonne limit in force today, and track your cumulative tonnage across all CBAM goods so you know which side of it you fall.
What Assofermet asked for
The association says it has put the request to the Commission so that extending CBAM to downstream products does not bring disproportionate paperwork for businesses (Assofermet, in Italian). According to SteelOrbis, which reported the letter on 11 November, it went to Commission President Ursula von der Leyen and to the tax and climate directorates, DG TAXUD and DG CLIMA. Assofermet argues that a finished article can weigh far more than the steel or aluminium in it, so a single tonnage limit could be disproportionate for small importers of goods such as hardware, tools and machinery parts. It cites earlier Commission analysis showing that, at 500 tonnes, about 97% of importers would fall outside CBAM yet 96.43% of embedded emissions in the original sectors would still be covered, and asks for a new impact assessment, possibly with limits by product group, plus anti-circumvention checks.
Reach steel buyers and importers worldwide
Put your brand in front of the people who buy and trade steel.
Advertise with LoharoThe rule today is in Regulation (EU) 2025/2083. An importer is exempt when the net mass of all its CBAM goods (iron and steel, aluminium, cement and fertilisers together) does not exceed 50 tonnes in a calendar year. Cross it, and every tonne imported that year falls under CBAM, not just the excess. The limit is designed to keep at least 99% of embedded emissions in scope; the Commission reviews it each year and can change it by delegated act.
Two sources, two directions
Analysis. The request runs against Parliament’s mandate. In our 22 October report on the downstream talks we put Parliament’s list at 457 products; Assofermet speaks of about 500 categories. Both refer to the position adopted on 15 September; we keep the 457 from Parliament’s text and treat Assofermet’s figure as a rounded one. What is new since then is the threshold. Law firm Mayer Brown reads Parliament’s text as cutting the limit for aluminium goods from 50 to 5 tonnes, while the Commission and EU governments keep 50 tonnes. Assofermet wants it ten times higher. According to Mayer Brown, the second political round of talks is provisionally set for 30 November.
Loharo calculation: what each limit means for a small coil importer
| Hot-rolled coil imported in 2026 (CN 7208) | India | China | Türkiye | Under today’s 50 t limit | Under a 500 t limit |
|---|---|---|---|---|---|
| 49 t | €0 | €0 | €0 | Exempt | Exempt |
| 51 t | €14,159 | €9,138 | €5,598 | All 51 t in scope | Exempt |
| 200 t | €55,484 | €35,727 | €21,979 | In scope | Exempt |
| 500 t | €138,792 | €89,317 | €54,990 | In scope | Exempt |
Analysis. The table shows the cliff in today’s rule: the 51st tonne of Indian coil costs about €14,000, because it pulls the first 50 into scope too. Verified supplier emissions below the default would lower every figure; the free calculator shows by how much.
What it means for buyers
Buyer or fabricator: if you import between 50 and 500 tonnes a year, a 500-tonne limit would remove both the declaration and the certificate bill, but only if negotiators adopt it; plan on today’s rule. EU mill: a higher limit would let more small lots of imported coil and finished goods enter without a carbon cost; steelmakers have asked negotiators for the broadest possible extension, as our October report set out. Distributor or service centre: remember that the limit is per importer across all CBAM goods, so a few tonnes of aluminium or fasteners count towards it alongside coil.
What would change this view: a trilogue text that sets product-specific limits, or a Commission review that moves the 50 tonnes. Next watch: the round of talks set for 30 November, and the Q4 2026 certificate price due on 4 January.
Verification status: Verified
The request is confirmed by Assofermet’s own release; the letter’s recipients and the 97% and 96.43% figures are attributed to SteelOrbis’ report of it. The 50-tonne rule is checked against EUR-Lex, Parliament’s aluminium limit is Mayer Brown’s reading, and the cost table is a Loharo calculation on official default values, not a customs liability.
Ask the Analyst
“What could CBAM add to Indian HRC delivered to Rotterdam in 2027?”: landed cost with duty, quota and CBAM in one answer.Ask the AnalystSources
Primary sources
- CBAM: Assofermet sottopone alla Commissione europea la richiesta di rivedere la soglia de minimis da 50 a 500 tonnellate annue per importatore — Assofermet, November 2026 (Italian)
- Regulation (EU) 2025/2083 amending the CBAM Regulation (Article 2a and Annex VII, de minimis exemption) — EUR-Lex, 17 October 2025
- Implementing Regulation (EU) 2026/1740 (default values), Implementing Regulation (EU) 2025/2620 (benchmarks) and Directive (EU) 2023/959 (CBAM factors) — EUR-Lex
- Price of CBAM certificates — European Commission, checked 13 November 2026
Supporting sources
- Assofermet calls on EU to raise CBAM exemption threshold to 500 mt — SteelOrbis, 11 November 2026
- EU’s CBAM downstream extension and anti-circumvention amendments: the road to trilogue — Mayer Brown, October 2026
- EU opens CBAM downstream talks and free CBAM calculator — Loharo
Last fact-check: 13 November 2026. Market intelligence, not legal or investment advice.




