• EU HRC (N. Europe)€750–785/tex-works N. Europe; seller tradeable €770–780/t for January volumes; buyer indications €750–765/t and €780–785/t ex-works; Fastmarkets index €770.83/t on 12 Nov12 Nov 2026 · Fastmarkets via EUROMETAL
  • China steel exports9.854 MtOctober; Jan–Oct 95.495 Mt, −2.3% y/y10 Nov 2026 · China Customs via Mysteel / SMM
  • World crude steel142.4 MtSeptember, −0.2% y/y23 Oct 2026 · worldsteel
  • Iron ore fines 61%$90.35/dmtseaborne 61% fines, SMM; +$0.15/dmt d/d13 Nov 2026 · SMM via Hellenic Shipping News
  • Turkish HMS 1&2 (80:20)$397/tCFR, October average11 Nov 2026 · GMK Center
  • EU CBAM certificate€82.32Q3 2026 price, per certificate5 Oct 2026 · European Commission
  • US Section 232 steel10%–50%tariff, by product/country8 Oct 2026 · Congressional Research Service

China’s October steel output falls 1.6% to 70.83 Mt; Loharo’s scenarios put 2026 at 928–945 Mt, down 1.6–3.4%

China made 70.83 Mt of crude steel in October, 1.6% less than a year earlier, and its daily rate fell about 7% from September. Loharo’s scenarios put full-year output 1.6–3.4% below 2025. Little of it can enter the EU directly: most of China’s quota lines are full, with room left only in tin mill and stainless cold-rolled.

By Kunal VartakPublished 7 min read
Illustration: a row of domed hot-blast stoves with large hot-blast pipework at an integrated steelworks at dawn
Illustration of hot-blast stoves at an integrated steelworks at dawn

China made 70.83 million tonnes (Mt) of crude steel in October, 1.6% less than a year earlier, the National Bureau of Statistics (NBS) said on 16 November (NBS, in Chinese). Per calendar day, output fell about 7% from September, a little more than last year’s seasonal dip, so mills are trimming, but only modestly. For EU buyers the direct effect is limited: China’s own fourth-quarter EU quota for hot-rolled coil is 41 tonnes and 11 of its 22 country quota lines are used up, so most Chinese steel pays the 50% out-of-quota duty. No step is needed yet for flat-steel buyers. If you buy Chinese tin mill products or stainless cold-rolled strip, where quota room remains, check the line in Loharo’s Steel Trade Measures Tracker before booking arrival this year.

What NBS reported

Pig iron output fell 4.1% year on year to 63.07 Mt in October and finished-steel output fell 5.1% to 111.61 Mt. For January–October, crude steel was 795.61 Mt (−2.8%), pig iron 691.52 Mt (−3.1%) and finished steel 1,173.48 Mt (−2.6%). Value added in iron and steel smelting and rolling fell 1.7% in October. Construction demand kept shrinking: investment in real estate development fell 21.6% in the first ten months (NBS, English summary), after −20.6% to September, as we reported in our September output report.

Advertise

Reach steel buyers and importers worldwide

Put your brand in front of the people who buy and trade steel.

Advertise with Loharo

Loharo calculation: how much did mills cut?

MeasureSeptember 2026October 2026Change per calendar day
Crude steel73.59 Mt (2.453 Mt/day)70.83 Mt (2.285 Mt/day)−6.9%
Pig iron65.34 Mt (2.178 Mt/day)63.07 Mt (2.035 Mt/day)−6.6%
Finished steel118.17 Mt (3.939 Mt/day)111.61 Mt (3.600 Mt/day)−8.6%
Finished-steel exports (customs)10.49 Mt9.85 Mt−9.1%
Exports as a share of finished-steel output8.9%8.8%—
Loharo calculation. Monthly totals divided by calendar days (30 and 31), the method NBS uses for its own daily averages. Output: NBS releases for September and October 2026. Exports: customs data as reported by SteelOrbis and in our October exports report. Production and customs figures come from different surveys, so the export share is indicative.

Analysis Loharo check against last year: in 2025, daily crude output fell 5.2% from September to October (73.49 Mt to 72.00 Mt; NBS releases for September and October 2025). This year’s 6.9% fall is about 1.7 points steeper, and year-on-year output turned from +0.1% in September to −1.6%. The figures reconcile: January–September output of 724.77 Mt plus October’s 70.83 Mt gives 795.60 Mt, against 795.61 Mt reported; and 70.83 ÷ 72.00 − 1 = −1.6%. Finished output and exports fell by similar proportions, so the share of output exported held at about 9%, above the 8.1% average for January–October (95.50 ÷ 1,173.48).

Loharo scenarios: where 2026 output could end

If November–December output runs at…Nov–Dec outputFull-year 2026vs 2025 (960.81 Mt)
September’s daily rate (2.453 Mt/day)149.6 Mt945.2 Mt−1.6%
October’s daily rate (2.285 Mt/day)139.4 Mt935.0 Mt−2.7%
the same level as November–December 2025 (69.87 + 68.18 Mt)138.1 Mt933.7 Mt−2.8%
5% below October’s daily rate (deeper winter cuts)132.4 Mt928.0 Mt−3.4%
Loharo calculation. January–October 2026 output of 795.61 Mt (NBS) plus 61 days at each rate. 2025 figures: November 69.87 Mt (NBS); December 68.18 Mt and full year 960.81 Mt (NBS data as reported by CCTD, in Chinese). NBS calculates its own growth rates on a comparable sample of companies, so its published full-year change may differ by a few tenths of a point. These are scenarios, not forecasts.

Analysis On every path, China’s output ends 2026 between about 1.6% and 3.4% lower, a smaller cut than 2025’s 4.4%, while property investment keeps falling by more than a fifth. NBS does not publish steel consumption, so the data do not show directly how much steel is left over; but unless demand outside construction makes up the difference, the pressure to export or stock steel stays. That is an inference, not something the October data show.

What has changed since our 2 November report

Our 2 November report estimated, from China Iron and Steel Association figures, that China made about 100 Mt more crude steel than it used at home in January–September, and said the October NBS data would show whether mills were cutting output as the association asked. The answer is: yes, modestly. The daily rate fell faster than last year’s seasonal pattern and output is now below last year’s level, but the cut is small next to the fall in construction activity. The October data do not update the 100 Mt estimate, because they contain no consumption figure.

What it means for EU buyers

Analysis Very little of this steel can come straight into the EU. In the Commission’s 13 November quota report, as shown in Loharo’s Tracker, China’s own Q4 hot-rolled coil line (09.9816) is 41 tonnes; 11 of its 22 lines have no balance left; rebar (25 t left), merchant bars (75 t) and cold-finished bars (70 t, down from 249 t on 6 November) are effectively closed; and stainless hot-rolled strip has 1,210 t left and is flagged at risk. Real room remains only in tin mill products (39,692 t of 52,800 t) and stainless cold-rolled strip (14,490 t of 15,855 t). Above quota, imports pay 50% (our guide to the regime). The indirect risk is in third markets, where Asian mills that also sell to Europe compete with Chinese exports.

Analysis For your contracts: if you book Chinese tin mill or stainless cold-rolled material for clearance before 31 December, state who pays the 50% out-of-quota duty if the line is used up before customs clearance, and check any anti-dumping duty that applies to the product.

Stay ahead of the steel market

We’ll email you a confirmation link. Unsubscribe anytime. See our Privacy Policy.

What to watch

  • Around 20 November: China’s detailed October export breakdown by product and destination.
  • Weekly Commission quota report: China’s stainless hot-rolled (1,210 t) and tin mill lines, in Loharo’s Tracker.
  • Mid-December: NBS November output, to see which scenario row 2026 is following.
  • 1 January 2027: EU quotas for the first quarter of 2027 open.

Verification status: Verified

  • China’s production, smelting value added and property investment figures come from NBS’s 16 November release (Chinese table and English summary) and its 2025 and September 2026 monthly releases, with the 2025 December and full-year totals as reported by CCTD; export figures are customs data reported by SteelOrbis; quota balances come from the Commission’s 13 November report via Loharo’s Tracker, matching TARIC. Daily rates, the export share and the full-year scenarios are Loharo calculations with inputs shown.
  • Key: Verified = material factual claims are supported by an appropriate primary source or clearly attributed reporting/market assessments; Partially verified = a specific material claim remains unsupported, contradicted or materially overstated; Analysis = interpretation or forecast with sourced premises; Developing = material facts are checked but the situation is still changing.

Sources

Primary sources

Supporting sources

Last fact-check: 16 November 2026.

Planning steel imports into the EU? Estimate CBAM costs with the free calculator using EU default values. For supplier-specific emissions and a portfolio review, see the CBAM Cost Check.

Ask the Analyst

“1,000 t HRC from China into Rotterdam at €540/t CFR”: landed cost with duty, quota and CBAM in one answer.Ask the Analyst

Facts, analysis and uncertainty are labelled in line with our editorial standards. Report an error – corrections are dated and noted on the article. Information and analysis only, not investment advice.