China made 70.83 million tonnes (Mt) of crude steel in October, 1.6% less than a year earlier, the National Bureau of Statistics (NBS) said on 16 November (NBS, in Chinese). Per calendar day, output fell about 7% from September, a little more than last year’s seasonal dip, so mills are trimming, but only modestly. For EU buyers the direct effect is limited: China’s own fourth-quarter EU quota for hot-rolled coil is 41 tonnes and 11 of its 22 country quota lines are used up, so most Chinese steel pays the 50% out-of-quota duty. No step is needed yet for flat-steel buyers. If you buy Chinese tin mill products or stainless cold-rolled strip, where quota room remains, check the line in Loharo’s Steel Trade Measures Tracker before booking arrival this year.
What NBS reported
Pig iron output fell 4.1% year on year to 63.07 Mt in October and finished-steel output fell 5.1% to 111.61 Mt. For January–October, crude steel was 795.61 Mt (−2.8%), pig iron 691.52 Mt (−3.1%) and finished steel 1,173.48 Mt (−2.6%). Value added in iron and steel smelting and rolling fell 1.7% in October. Construction demand kept shrinking: investment in real estate development fell 21.6% in the first ten months (NBS, English summary), after −20.6% to September, as we reported in our September output report.
Reach steel buyers and importers worldwide
Put your brand in front of the people who buy and trade steel.
Advertise with LoharoLoharo calculation: how much did mills cut?
| Measure | September 2026 | October 2026 | Change per calendar day |
|---|---|---|---|
| Crude steel | 73.59 Mt (2.453 Mt/day) | 70.83 Mt (2.285 Mt/day) | −6.9% |
| Pig iron | 65.34 Mt (2.178 Mt/day) | 63.07 Mt (2.035 Mt/day) | −6.6% |
| Finished steel | 118.17 Mt (3.939 Mt/day) | 111.61 Mt (3.600 Mt/day) | −8.6% |
| Finished-steel exports (customs) | 10.49 Mt | 9.85 Mt | −9.1% |
| Exports as a share of finished-steel output | 8.9% | 8.8% | — |
Analysis Loharo check against last year: in 2025, daily crude output fell 5.2% from September to October (73.49 Mt to 72.00 Mt; NBS releases for September and October 2025). This year’s 6.9% fall is about 1.7 points steeper, and year-on-year output turned from +0.1% in September to −1.6%. The figures reconcile: January–September output of 724.77 Mt plus October’s 70.83 Mt gives 795.60 Mt, against 795.61 Mt reported; and 70.83 ÷ 72.00 − 1 = −1.6%. Finished output and exports fell by similar proportions, so the share of output exported held at about 9%, above the 8.1% average for January–October (95.50 ÷ 1,173.48).
Loharo scenarios: where 2026 output could end
| If November–December output runs at… | Nov–Dec output | Full-year 2026 | vs 2025 (960.81 Mt) |
|---|---|---|---|
| September’s daily rate (2.453 Mt/day) | 149.6 Mt | 945.2 Mt | −1.6% |
| October’s daily rate (2.285 Mt/day) | 139.4 Mt | 935.0 Mt | −2.7% |
| the same level as November–December 2025 (69.87 + 68.18 Mt) | 138.1 Mt | 933.7 Mt | −2.8% |
| 5% below October’s daily rate (deeper winter cuts) | 132.4 Mt | 928.0 Mt | −3.4% |
Analysis On every path, China’s output ends 2026 between about 1.6% and 3.4% lower, a smaller cut than 2025’s 4.4%, while property investment keeps falling by more than a fifth. NBS does not publish steel consumption, so the data do not show directly how much steel is left over; but unless demand outside construction makes up the difference, the pressure to export or stock steel stays. That is an inference, not something the October data show.
What has changed since our 2 November report
Our 2 November report estimated, from China Iron and Steel Association figures, that China made about 100 Mt more crude steel than it used at home in January–September, and said the October NBS data would show whether mills were cutting output as the association asked. The answer is: yes, modestly. The daily rate fell faster than last year’s seasonal pattern and output is now below last year’s level, but the cut is small next to the fall in construction activity. The October data do not update the 100 Mt estimate, because they contain no consumption figure.
What it means for EU buyers
Analysis Very little of this steel can come straight into the EU. In the Commission’s 13 November quota report, as shown in Loharo’s Tracker, China’s own Q4 hot-rolled coil line (09.9816) is 41 tonnes; 11 of its 22 lines have no balance left; rebar (25 t left), merchant bars (75 t) and cold-finished bars (70 t, down from 249 t on 6 November) are effectively closed; and stainless hot-rolled strip has 1,210 t left and is flagged at risk. Real room remains only in tin mill products (39,692 t of 52,800 t) and stainless cold-rolled strip (14,490 t of 15,855 t). Above quota, imports pay 50% (our guide to the regime). The indirect risk is in third markets, where Asian mills that also sell to Europe compete with Chinese exports.
Analysis For your contracts: if you book Chinese tin mill or stainless cold-rolled material for clearance before 31 December, state who pays the 50% out-of-quota duty if the line is used up before customs clearance, and check any anti-dumping duty that applies to the product.
Stay ahead of the steel market
What to watch
- Around 20 November: China’s detailed October export breakdown by product and destination.
- Weekly Commission quota report: China’s stainless hot-rolled (1,210 t) and tin mill lines, in Loharo’s Tracker.
- Mid-December: NBS November output, to see which scenario row 2026 is following.
- 1 January 2027: EU quotas for the first quarter of 2027 open.
Verification status: Verified
- China’s production, smelting value added and property investment figures come from NBS’s 16 November release (Chinese table and English summary) and its 2025 and September 2026 monthly releases, with the 2025 December and full-year totals as reported by CCTD; export figures are customs data reported by SteelOrbis; quota balances come from the Commission’s 13 November report via Loharo’s Tracker, matching TARIC. Daily rates, the export share and the full-year scenarios are Loharo calculations with inputs shown.
- Key: Verified = material factual claims are supported by an appropriate primary source or clearly attributed reporting/market assessments; Partially verified = a specific material claim remains unsupported, contradicted or materially overstated; Analysis = interpretation or forecast with sourced premises; Developing = material facts are checked but the situation is still changing.
Sources
Primary sources
- 2026年10月份规模以上工业增加值增长4.8% (October 2026 industrial production, in Chinese), National Bureau of Statistics of China, 16 November 2026
- National Economy was Generally Stable with Innovation-Led and High-Quality Development in October, National Bureau of Statistics of China (via gov.cn), 16 November 2026
- NBS monthly industrial production releases (in Chinese): September 2026, September 2025, October 2025 and November 2025
- Commission weekly report on tariff quota imports of 13 November 2026 (DG TAXUD), as read in Loharo’s Steel Trade Measures Tracker on 16 November 2026; China lines checked in TARIC (last update 13 November 2026): 09.9816 hot-rolled coil, 09.9848 tin mill, 09.9868 stainless cold-rolled and 09.9863 stainless hot-rolled
Supporting sources
- 2025年全国粗钢和生铁产量降至多年低点 (2025 crude steel and pig iron output at multi-year lows, in Chinese), CCTD China Coal Market Network, citing NBS, 20 January 2026
- China’s steel exports down 2.3% in Jan-Oct, down 6.1% in Oct from Sept 2026, SteelOrbis, November 2026
- 国家统计局:1-10月中国粗钢产量79561万吨,同比降2.8% (NBS: Jan–Oct crude steel 795.61 Mt, in Chinese), Mysteel, 16 November 2026
Last fact-check: 16 November 2026.
Planning steel imports into the EU? Estimate CBAM costs with the free calculator using EU default values. For supplier-specific emissions and a portfolio review, see the CBAM Cost Check.




